PIC16F87T-E/ML【PDF 199/200 页】IC MCU FLASH 4KX14 EEPROM 28QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3882

195页 196页 197页 198页 [199页]200页

8008H–AVR–04/11

ATtiny48/88

The OCR1x Register is double buffered when using any of the twelve Pulse Width Modulation

(PWM) modes. For the Normal and Clear Timer on Compare (CTC) modes of operation, the

double buffering is disabled. The double buffering synchronizes the update of the OCR1x Com-

pare Register to either TOP or BOTTOM of the counting sequence. The synchronization

prevents the occurrence of odd-length, non-symmetrical PWM pulses, thereby making the out-

put glitch-free.

The OCR1x Register access may seem complex, but this is not case. When the double buffering

is enabled, the CPU has access to the OCR1x Buffer Register, and if double buffering is dis-

abled the CPU will access the OCR1x directly. The content of the OCR1x (Buffer or Compare)

automatically as the TCNT1 and ICR1 Register). Therefore OCR1x is not read via the high byte

temporary register (TEMP). However, it is a good practice to read the low byte first as when

accessing other 16-bit registers. Writing the OCR1x Registers must be done via the TEMP Reg-

ister since the compare of all 16 bits is done continuously. The high byte (OCR1xH) has to be

written first. When the high byte I/O location is written by the CPU, the TEMP Register will be

updated by the value written. Then when the low byte (OCR1xL) is written to the lower eight bits,

the high byte will be copied into the upper 8-bits of either the OCR1x buffer or OCR1x Compare

For more information of how to access the 16-bit registers refer to “Accessing 16-bit Registers”

on page 91.

12.7.1

Force Output Compare

In non-PWM Waveform Generation modes, the match output of the comparator can be forced by

writing a one to the Force Output Compare (FOC1x) bit. Forcing compare match will not set the

OCF1x Flag or reload/clear the timer, but the OC1x pin will be updated as if a real compare

match had occurred (the COM1[1:0] bits settings define whether the OC1x pin is set, cleared or

toggled).

12.7.2

Compare Match Blocking by TCNT1 Write

All CPU writes to the TCNT1 Register will block any compare match that occurs in the next timer

clock cycle, even when the timer is stopped. This feature allows OCR1x to be initialized to the

same value as TCNT1 without triggering an interrupt when the Timer/Counter clock is enabled.

12.7.3

Using the Output Compare Unit

Since writing TCNT1 in any mode of operation will block all compare matches for one timer clock

cycle, there are risks involved when changing TCNT1 when using any of the Output Compare

channels, independent of whether the Timer/Counter is running or not. If the value written to

TCNT1 equals the OCR1x value, the compare match will be missed, resulting in incorrect wave-

form generation. Do not write the TCNT1 equal to TOP in PWM modes with variable TOP

values. The compare match for the TOP will be ignored and the counter will continue to 0xFFFF.

Similarly, do not write the TCNT1 value equal to BOTTOM when the counter is downcounting.

The setup of the OC1x should be performed before setting the Data Direction Register for the

port pin to output. The easiest way of setting the OC1x value is to use the Force Output Com-

pare (FOC1x) strobe bits in Normal mode. The OC1x Register keeps its value even when

changing between Waveform Generation modes.

Be aware that the COM1x[1:0] bits are not double buffered together with the compare value.

Changing the COM1x[1:0] bits will take effect immediately.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式